1988 Dodge B250 Driveline and Axles Parts
Choose your Part Name for your 1988 Dodge B250
Axle Differential Bearing
Axle Nut
Differential
Differential Cover Gasket
Differential Drive Pinion Gear Nut
Differential End Yoke
Differential Pinion Bearing
Differential Pinion Race
Differential Pinion Seal
Differential Ring Gear Bolt
Differential Ring and Pinion
Drive Axle Shaft Bearing
Drive Axle Shaft Bearing Kit
Drive Axle Shaft Seal
Drive Shaft Center Support
Drive Shaft Pinion Yoke Washer
Wheel Bearing
Wheel Bearing Race
Wheel Bearing and Race Set
Wheel Seal
Image
Product
Price
- Auburn Gear Ected Max Differential
- Open To Lock; Dana 70; 40 Spline; 4.10 Gear Ratio Down
- Auburn Gear Ected Max Differential; Open To Lock; Dana 70; 40 Spline; 4.10 Gear Ratio Down;
- Auburn Gear Ected Max
-
Features:
- Selectable Full Locker And Limited Slip In One Unit
- Can Be Engaged/Disengaged At Any Reasonable Speed
- Smooth Quiet Operation
- Can Be Use With Or Without Lockout Hubs
- Made From 9310 Heat Treated Billet Steel
- Backed By 1 Year Warranty
- Covered w/4 Year Differential-Replacement Exchange
- Made In The USA
- The ECTED Max is a selectable traction device; an on/off switch is mounted near the driver. When off–the clutch pack,located behind the side gear provides the limited slip mode. As torque increases, the separating forces within the differential gears increase, causing the clutch pack to be compressed and thereby providing bias torque to the high traction wheel–your performance limited slip differential action. When selected on, current is sent to the electromagnetic coil. The coil is retained by a clip that fits over one of the bearing cap bolts, making it non-rotational. The coil rides on a ball bearing. The ball bearings spin with the differential case. The coil creates a magnetic flux so that the pilot cone is pulled into engagement with the differential case. This frictional engagement causes the bearing balls to ride up on a ramp machined into the side gear. This radial travel of the balls also causes lateral movement of the side gear. This applies a force onto the center block. The center block has an elongated hole that the center pin fits through, allowing it to float. The center block applies force to the opposite side gear, compressing the clutch pack giving the user a solid axle assembly–the spool/locker performance you desire at the strip/off-road. ECTED Max gearing is made from aircraft quality, 9310 heat-treated billet steel. Tough as nails! ECTED Max can be switched on or off on the fly, at any road speed. ECTED Max does not have any shift forks or pins that must be lined up to obtain locker mode. ECTED Max is quiet. Good-bye to noisy lockers! ECTED Max is backed by industry-leading 1 year warranty, like all Auburn Gear Performance Differentials. ECTED Max is backed by the industry-exclusive program. D-REX=Differential–Replacement EXchange Program. ECTED Max can be used in front axle applications–with or w/out lockout hubs. ECTED Max is the only selectable locker offering both limited slip and locker modes. Forget the rest-go with the best!
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear |
- Differential Drive Pinion Gear Nut
- with Dana 60 Axle
- FSGR
- Product Attributes:
- California Proposition 65: Warning: Cancer And Reproductive Harm — Www.p65warnings.ca.gov
- Thread Size: .875-14
- Self Locking: Y
- Shaft Not Torque (Ft/Lbs): 47 Nm/20 To 35 Lbs
- Hex: 32.815mm
- Flange Diameter: 32.515mm
- Thickness: 15.875mm
-
Features:
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana.
- Tested and validated to rigorous OE specifications.
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace.
- Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.
This Part Fits the Following OEM/Substitute Numbers:
2510524C1, DS30271, SP 30271
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear Differential |
- PINION NUT WASHER
- with Dana 60 Axle
- FSGR
- Product Attributes:
- Inner Diameter: 0.898
- Outer Diameter: 1.500
- Thickness: 0.119
-
Features:
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana.
- Tested and validated to rigorous OE specifications.
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace.
- Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.
This Part Fits the Following OEM/Substitute Numbers:
2510523C1, AUH224501, DS30275, SP 30275
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear Differential |
- Differential Pinion Seal
- with Dana 60 Axle
- FSGR
- Product Attributes:
- Inside Diameter (In): 1.860
- Axle Model: Dana 60, Dana 70
-
Features:
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace.
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana.
- Tested and validated to rigorous OE specifications.
- Genuine Spicer light vehicle axle products are manufactured to the same high standards as original equipment (OE) parts because they are OE parts. That means when an automotive axle part is replaced with a genuine Spicer part, you are getting the same performance and reliability you have come to expect. And because Dana is constantly revolutionizing the technology behind its Dana axles and Spicer products, the replacement car axle or component you purchase today may even exceed the standards set for the original equipment part that you are replacing.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
816675, DS42449, SP 42449
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear |
- PINION SHAFT END YOKE
- U-Bolt Type with 29 Splines with Dana 1350 Series Drive Shaft with Dana 60 & 70 Axle(s)
- FSGR
- Product Attributes:
- Yoke Style: U-bolt
- O.D. of Spline: 1.276
- C/L To End Hub S: 3.000
- Length Thru Hole Q: 1.187
- Spline Count: 29
- Hub Diameter R: 1.500
-
Features:
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana
- Tested and validated to rigorous OE specifications
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace
- Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.
This Part Fits the Following OEM/Substitute Numbers:
YY D60-1350-29U
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear Differential |
- PINION SHAFT END YOKE
- with Dana 60 & 70 Axle(s) U-Bolt Type with 29 Splines with Dana 1350 Series Drive Shaft
- FSGR
- Product Attributes:
- Yoke Style: U-bolt
- O.D. of Spline: 1.276
- C/L To End Hub S: 3.000
- Length Thru Hole Q: 1.187
- Spline Count: 29
- Hub Diameter R: 1.500
-
Features:
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana
- Tested and validated to rigorous OE specifications
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace
- Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear Differential |
- Differential Drive Pinion Gear Nut
- with Dana 60 Axle
- FSGR
- Product Attributes:
- California Proposition 65: Warning: Cancer And Reproductive Harm — Www.p65warnings.ca.gov
- Thread Size: .875-14
- Self Locking: Y
- Shaft Not Torque (Ft/Lbs): 47 Nm/20 To 35 Lbs
- Hex: 32.815mm
- Flange Diameter: 32.515mm
- Thickness: 15.875mm
-
Features:
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana.
- Tested and validated to rigorous OE specifications.
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace.
- Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear Differential |
- PINION NUT WASHER
- with Dana 60 Axle
- FSGR
- Product Attributes:
- Inner Diameter: 0.898
- Outer Diameter: 1.500
- Thickness: 0.119
-
Features:
- Genuine OE quality. Tested and proven.
- Built to meet OE standards set by Dana.
- Tested and validated to rigorous OE specifications.
- Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace.
- Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear Differential |
- Differential Cover Gasket
- with 10 Bolt Holes with 8.375in Ring Gear ; Chrysler
- FEL-PRO RDS 55047 Differential Cover Gasket
- Fel-Pro® gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear |
- Differential Cover Gasket
- with 10 Bolt Holes with 8.25in Ring Gear ; Chrysler
- FEL-PRO RDS 55047 Differential Cover Gasket
- Fel-Pro® gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
This Part Fits the Following OEM/Substitute Numbers:
2852922, 36012, 4049689, DS14211, DT007, P18564, P18564TC
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 1988 - Dodge B250 | Rear |
Showing 1 - 10 of 72 products
Loading...