Image
Product
Price
- New CV Axle Shaft
- Updated Design
- New CV Axle Shaft
- AAR CV Axle Shaft
- Product Attributes:
- Outboard Bolt Head Size (mm): N/a
- Axle Nut Height (in): 0.91
- Axle Bolt Hex Size (mm): N/a
- Axle Nut Head Type: Hex
- Number Of Inboard Joint Bolt Holes: N/a
- Outboard Bolt Length (mm): N/a
- Outboard Bolt Head Type: N/a
- Axle Nut Hex Size (mm): 34.6
- Inboard Shaft Connection Style: Spline
- Inboard Bolt Length (in): N/a
- Axle Nut Thread Size: M26*1.5
- Axle Bolt Thread Size: N/a
- Number Of Outboard Joint Bolt Holes: N/a
- Axle Nut Length (mm): 39.95
- Axle Nut Locking Type: Stake
- Boot Material: Neoprene
- Inboard Bolt Head Size (in): N/a
- Number Of Inboard Shaft Bolts: N/a
- Outboard Bolt Head Size (in): N/a
- Inboard Joint Type: Male
- Overall Compressed Length (in): 26.89
- Abs Ring Type: N/a
- Axle Nut Hex Size (in): 1.36
- Number Of Inboard Splines: 31
- Axle Nut Height (mm): 23
- Number Of Outboard Shaft Bolts: N/a
- Outboard Joint Bolt Thread Size: N/a
- Outboard Bolt Length (in): N/a
- Outboard Joint Type: Conventional
- Axle Nut Included: Yes
- Inboard Bolt Head Size (mm): N/a
- Number Of Outboard Splines: 30
- Axle Bolt Length (mm): N/a
- Inboard Bolt Length (mm): N/a
- Outboard Shaft Connection Style: Spline
- Inboard Bolt Head Type: N/a
- Axle Nut Length (in): 1.57
- Overall Compressed Length (mm): 683
- Inboard Bolt Thread Size: N/a
- Limited Lifetime Warranty. ABS axles fit non-ABS applications unless otherwise noted. ISO 9001:1007 and TS 16949:2009 Certified Company
This Part Fits the Following OEM/Substitute Numbers:
44306TZ5A31, HO-8645
Additional Fitment Information:
| Vehicle | Block | CC | Position | Engine | CID |
|---|---|---|---|---|---|
| 2018 - Acura MDX | V | 3471 | Front Left | 6 Cyl 3.5L | - |
- Wheel Bearing and Hub Assembly
- MOOG 512544 Hub Assembly
- Product Attributes:
- Flange Bolt Hole Quantity: 4
- Anti Lock Brake Sensor Included: Yes
- Brake Pilot Diameter: 64.100
- Flange Offset: 58.800
- Bolt Circle Diameter: 114.300
- Hub Pilot Diameter: 72.000
- Wheel Pilot Diameter: 64.100
- Flange Diameter: 139.300
- Wheel Stud Quantity: 5
-
Features:
- RELIABLE PERFORMANCE -- Precise roll-form design ensures consistent and optimal factory-installed preload to minimize excessive noise and wear
- EXTENDED SERVICE LIFE -- Application-specific advanced raceway design reduces stress, rotation and heat on components
- KEEPS WATER AND DIRT OUT -- Quad lip seal design inhibits damage by keeping moisture and other contaminants out
- EASY TO INSTALL -- Engineered and designed for fast, hassle-free installation
- CORROSION PROTECTION -- Coated wheel studs resist corrosion and rust for easier removal and proper torqueing
- RIGOROUS TESTING -- Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- Backed by superior materials and rigorous testing, MOOG hub assemblies deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
-
Suggested Purchase Quantity: 2
- Most jobs typically require 2 of this item.
This Part Fits the Following OEM/Substitute Numbers:
051-6447, 42200-T2A-A51, BR930856, WE60616
Additional Fitment Information:
| Vehicle | Position | Drive Type |
|---|---|---|
| 2018 - Acura TLX | Rear | FWD |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2018 - Acura RDX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2018 - Acura ILX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- This bearing is equipped with an internal ABS sensor magnet. Care must be taken during installation to insure that the sensor magnet is located on the correct side of the bearing housing. Failure to do so may cause a malfunction in the ABS system. For more info, refer to the appropriate section of your service manual or check with your local dealer.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2018 - Acura ILX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2018 - Acura RDX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle | Position | Sub Model |
|---|---|---|
| 2018 - Acura TLX | Rear | Base |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- This bearing is equipped with an internal ABS sensor magnet. Care must be taken during installation to insure that the sensor magnet is located on the correct side of the bearing housing. Failure to do so may cause a malfunction in the ABS system. For more info, refer to the appropriate section of your repair manual or check with your local dealer.
Additional Fitment Information:
| Vehicle | Position |
|---|---|
| 2018 - Acura TLX | Front |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
- Carrier bearing ONLY. This bearing is also included with the right inner half-shaft stub axle.
Additional Fitment Information:
| Vehicle |
|---|
| 2018 - Acura TLX |
- This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
Additional Fitment Information:
| Vehicle |
|---|
| 2018 - Acura RDX |
Showing 1 - 10 of 237 products
Loading...